Re: 10GB ethernet - NIC recommendations
We currently use the Intel X520-2 Adapters in our hosts. Intel® Ethernet Converged Network Adapter X520 Product Family As for setup, we use A, Mgmt and Guest traffic on the two 10GbE uplinks. We use...
View ArticleClik here to view.
Re: vCO Port Issue when connecting to vCenter
The version/build of vCenter is 5.1.0 Build 1123961. I have tried a local admin, and since it's SSO I also tested admin@System-Domain (after granting it proper permissions in vCenter) both with...
View ArticleRe: Mixing Management and Backup traffic
If you only have one IP on your NFS target then traffic will only be able to flow through one physical uplink at any given point in time, so two teamed NICs are sufficient.OK - so I will have two...
View ArticleRe: Could not power on VM : Invalid metadata - storage
Is this is the only VM from that datastore facing this issue? Or multiple VMs? Also try to create a file inside the VM folder and see if that allow you to create files. If this is a Metadata corruption...
View ArticleClik here to view.
Re: Nested ESXi 5.1 Duplicate ICMP Response
Both vESXi-01 and vESXi-02 have changed to x1 uplink as below, but the duplicate ICMP issue still exist.
View ArticleRe: Console Blank (disconnected)
902 and 903 are not required externally, only from vCD cell to ESXi. TCP 443 to the console proxy address is needed. If you are not on 5.1.2, can you upgrade to vCloud Director 5.1.2? Also, check...
View ArticleRe: ESXi 5.0 and MSCS (Microsoft Failover Clustering) on iSCSI SAN
Offically VMware don't support MSCS on iSCSI SAN but you can use it. 2 VM's running on the same ESXI 5.0 host. > Since your running both VM's on same host its CIB config (Cluster in Box), where...
View ArticleRe: Nested ESXi 5.1 Duplicate ICMP Response
"10000 Full"!? Which virtual adapter do you use? Not sure whether this causes the issue, but afaik only the E1000 adapter is supported for virtual ESXi hosts. André
View ArticleRe: ESXi 5.0 and MSCS (Microsoft Failover Clustering) on iSCSI SAN
refer to this http://pubs.vmware.com/vsphere-50/topic/com.vmware.ICbase/PDF/vsphere-esxi-vcenter-server-50-mscs-guide.pdf...
View ArticleUnable to start the UI on ESXi5
Hi Everybody, This is Sankar From India. We have installed VMware ESXi 5 on Dell Poweredge 820. I am unable to open the UI and its showing 503 error.I have enabled the ssh and shell access.I didn't...
View ArticleRe: Can't Deploy Configuration
there is more to this error message ... there has to be. If need be, trigger uber mode and enable debug view and try again. then take a screen capture of the error state. Trigger Uber As System Admin...
View ArticleAccessing Hands-on Labs
How long does it usually take to get access after you have signed up for the Hands-On Labs ?
View ArticleRe: does gemfire multi-site gateway-hub support clear operation?
Yao, You can set up a command region that is gateway enabled. Then use that region to propagate commands (like region clear) between sites. You can use a CacheWriter to actually process the command....
View ArticleRe: Problem while running Quickstart FunctionExectution
Hi, You should provide full artifacts including all code along with changes and any config files. You need to also provide the full stacktrace and log which should point to a more specific point in the...
View ArticleRe: Wrong screen resolution in full screen for OS X 10.8.4 & 10.9
I'm seeing the same issue in the 10.9 DP 3. Thus, I have reinstalled the VMWare tools after installing 10.9 DP 3 and no success. If anyone has any ideas as to how to resolve this issue, it would be...
View ArticleRe: Mala recepción de trafico con VMware Server!!
Hola, te recomiendo cambiar a VMware Workstation debido a que vmware server está prácticamente obsoleto, ya no tiene soporte ni lo siguen manteniendo, no quiero decir que con esto tu problema se...
View ArticleRe: ESXI5.1 and Vlan
Dear Julien,this has been done however its not working yet no ping is alive !
View ArticleClik here to view.
Re: Can't Deploy Configuration
Thanks for the assistance! It was already in debug mode, but I just cleared the cache, ran the deployment again and took a screenshot:
View ArticleClik here to view.
Re: vCO Port Issue when connecting to vCenter
I am using the same vCenter (Windows Server Installation) version 5.1.0 build 1123961 and vCenter Orchestrator (Linux Appliance) version 5.1.1 build 2942.vCenter Server:vCenter Orchestrator: Something...
View Article